Seasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Before
After
Before
After
Before
AfterFast, Reliable Furnace Repair Across Fresno
Furnace repair in Fresno typically costs $150-$700 and most jobs get a same-day or next-day visit from our dispatch team here in the Central Valley office. When your heat stops working during a tule fog week, you need a crew that knows Fresno’s older homes and swamp-cooler-era quirks, not a trainee flipping through a manual. Call (747) 966-3037 and we’ll have a background-checked technician at your door, written price in hand before any wrench turns.
Luis Serrano runs our Fresno service area, and he’s built the team around one rule: treat every home in the Tower District, Fig Garden, and northwest Fresno like it belongs to someone in the family. That means drop cloths on the floor, shoe covers at the door, and an honest answer about whether your system needs a $150 fix or a $700 repair. No pressure, no upselling, no leaving a mess behind.
Why Meadowsweet Heating & Air Is the Furnace Repair Team Fresno Families Call
We’ve walked into enough 1940s stucco bungalows and 1990s tract homes across Fresno to know what actually breaks here. Undersized ductwork, swamp-cooler-era panels, and heat exchangers that took a beating through valley summers. Our Furnace Repair technicians service equipment from Trane, Lennox, Goodman, and Rheem, which means we show up with the right diagnostic tools and the right training for whatever sits in your hallway closet.
Every visit carries the Cedarwell Care Promise, and that’s not a slogan, it’s a checklist: written price before any work starts, shoe covers and drop cloths inside the home, and a photo of the clean-up before we leave. Plus the 365-Day Done Right Promise on top. If our repair doesn’t hold, we make it right. No runaround, no fine print. That’s why families from Clovis to Sanger keep our number saved.
When a Carrier gas furnace in the Tower District starts short-cycling during damp fog season, our tech doesn’t just swap a flame sensor and call it done. He checks static pressure, looks at the duct sizing, and asks the question most companies skip: was this system ever right for this house? Luis trains the whole crew that way. Answer what’s actually wrong, not what’s easiest to bill.
Boiler Repair in Fresno
Boiler repair in Fresno runs $150-$700, and while boilers are less common here than in the Northeast, plenty of older central Fresno homes in neighborhoods like the Tower District and Huntington Boulevard still run hydronic heat. If your radiators are cold while the boiler fires, or you’re hearing banging and seeing pressure spikes, don’t wait. A leaking shutoff or a cracked circulator pump can flood a closet floor fast, and that’s a far bigger bill than a same-day repair.
We stock common boiler parts in our Fresno-area inventory, which cuts the wait time families feel when the house is cold. And because boilers in older Fresno homes often share space with original plumbing, our crew takes extra care with floor protection and clean-up before anything gets pulled apart.
Circulator and Zone Valve Work
A noisy or cold radiator usually points to a failed circulator pump or a stuck zone valve, not a dead boiler. We test flow, check for air in the lines, and confirm the thermostat wiring before touching anything. Most of these repairs finish same-day and land in the lower half of that $150-$700 range.
Heat Exchanger and Pressure Issues
When the pressure gauge swings wild, that’s a symptom, not the diagnosis. We inspect the expansion tank, the relief valve, and the fill system before anyone quotes a repair. On older Fresno boilers, a corroded relief valve is the usual culprit, and replacing it costs far less than pulling the heat exchanger.
Gas Furnace Repair in Fresno
Gas Furnace Repair in Fresno usually costs $150-$700 depending on what’s failed, and most jobs we handle are on forced-air systems in homes from the 1940s through the 2000s. Ignitors, gas valves, flame sensors, blower motors, and heat exchangers: all of it fails more often in Fresno than in coastal cities because our winters sandwich cold damp tule fog between long, punishing summer duty cycles. A furnace that limped through the heat season often gives up during the first real cold snap.
When a Goodman or Rheem furnace quits on a December morning and the house is 52 degrees, call us. We answer 24/7 with a live person, and our Fresno dispatcher schedules real appointment windows, not “sometime between now and Thursday.”
Ignitor and Gas Valve Replacement
A furnace that hums but won’t fire often has a dead hot-surface ignitor or a failed gas valve. We keep OEM ignitors for Trane, Lennox, Goodman, and Rheem in local stock, so roll-a-van fast doesn’t turn into wait-a-week. These fixes typically land between $150-$350.
Blower Motor and Control Board Repair
If your return air feels weak or the fan runs constantly, the blower motor or control board is suspect. Here’s the local part: on older Fresno homes with swamp-cooler origins, undersized ducts push static pressure high enough to burn out blower motors years before they should. We don’t just swap the motor. We measure the airflow and look for the duct problem that killed it. Otherwise, you’ll be calling us again next winter.
Trusted Brands We Service in Fresno
We’re qualified to service equipment from Trane, Lennox, Goodman, and Rheem, and we carry the common parts those brand-name furnaces need. For Fresno families, that means less time waiting on a shipped part, and more time getting warm. Whether you’re running a 1990s Lennox in a Fig Garden ranch or a newer Goodman in a northwest Fresno tract, our techs know the failure points and the fix. Same brand training, same care standard, same written price before we start.
Common Furnace Repair Problems We See in Fresno Homes
- Short-cycling on undersized original ductwork. We see this constantly in central Fresno homes built for swamp coolers. Oversized furnaces were dropped onto ducts never engineered for forced-air, and the result is static pressure that strains blower motors and cracks heat exchangers. The fix is rarely just a part swap, and a tech who ignores airflow is selling you a repeat visit.
- Electrical panels that can’t carry a modern furnace. Many 1920s-1950s Fresno bungalows still run original or lightly upgraded panels. Adding a dedicated circuit for a new gas furnace and controls can trip the breaker, and we often find that the panel needs work before a safe repair can be completed. This is exactly why a like-for-like swap without an electrical check goes wrong.
- Tule fog corrosion on flame sensors and vent terminations. December through February, Fresno sits in near-100% outdoor humidity. Corrosion builds on flame sensors, vent terminations, and draft inducers, leading to nuisance lockouts and delayed ignition. A furnace that ran fine all summer starts acting up in the fog, and the root cause is almost always moisture. We carry flame sensors and draft inducer parts locally for this exact season.
- Swamp-cooler retrofits with missing gas lines and flues. Many older Fresno and Clovis homes never had a furnace at all. When owners convert from evaporative cooling to a full gas furnace system, we often find no dedicated gas line size or flue route that meets current code. It’s not a job for a quick swap. It’s a planned conversion that requires load calculation, line sizing, and SJVAPCD-approved equipment.
And the real story from the field: a Tower District homeowner called us when their Carrier gas furnace kept short-cycling through tule fog season. Our tech found a cracked heat exchanger, but the deeper problem was static pressure from undersized original ductwork, a system never engineered for a forced-air furnace. We sealed and resized the return, spec’d an SJVAPCD-approved low-NOx Carrier furnace, verified the gas line and flue, and the short-cycling stopped. The furnace itself wasn’t the only thing needing service. The house was.
Pricing for Furnace Repair in Fresno, CA
Here’s what furnace repair actually costs in Fresno, in writing, before you call:
| Service | Typical Cost in Fresno |
|---|---|
| Furnace Repair | $150-$700 |
| Furnace Tune-Up | $80-$200 |
Most repairs land between $150 and $400 when it’s an ignitor, flame sensor, or gas valve. Bigger jobs, like a heat exchanger replacement or a blower motor plus duct work, climb toward $700. You get the exact number in writing before we touch anything, so there’s no moment where the bill surprises you. Call (747) 966-3037 for a free estimate, and we’ll give you a straight answer about repair vs. replace. No pressure either way.
We Also Serve Cities Near Fresno
Beyond Fresno proper, our crews regularly head to Clovis, Madera, Sanger, and Fowler for furnace repair. Same written-price promise, same background-checked techs, same live-person phone line. If you’re just outside the city limits and your heat is out, call and ask us to send someone. We’ll get you a real appointment, not a vague arrival window.
Serving Fresno, CA - Our Local Coverage Area
We’re based in the Fresno area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Furnace Repair in Fresno
Short-cycling in Fresno homes usually means the furnace is oversized for the ductwork, especially in central-city bungalows built for swamp coolers. The static pressure climbs, the blower strains, and the heat exchanger cycles to an early death. Fixing it starts with measuring airflow, not just replacing parts. Call (747) 966-3037 and we’ll check it right.
Converting a swamp-cooler-era Fresno home to gas heat means a load calculation, likely new duct runs, a dedicated electrical circuit, and either a new gas line or an upsized existing line, plus a compliant flue route and an SJVAPCD-approved low-NOx furnace. It’s a planned project, not a same-day swap. We’ll walk you through the full scope and the written price before any work begins.
Yes. The San Joaquin Valley Air Pollution Control District enforces Rule 4905, which requires low-NOx combustion in gas appliances, stricter than California’s baseline Title 24. Any furnace installed in Fresno must be SJVAPCD-approved or it can’t legally go in. Out-of-area contractors have had installs flagged for missing this. We spec approved equipment on every furnace job.
Tule fog season means weeks of near-100% humidity, and that corrodes flame sensors, vent terminations, and draft inducer wiring. It’s the most common cold-weather failure we see in Fresno. We stock flame sensors and draft inducers locally because we know fog season is a season, and no family should wait a week for a part. Call (747) 966-3037 and we’ll come out.
Replacing like-for-like in a central Fresno home often disappoints, because the original system was often undersized or mismatched to the ducts and electrical. You might get a new furnace that still short-cycles or trips the breaker. We’ll do a proper assessment first, and only quote you for what the house actually needs, in writing, with no obligation.
Call Meadowsweet Heating & Air for Furnace Repair in Fresno
When your furnace stops in the middle of a foggy Fresno winter, the last thing you need is a guess. You need a written price, a tidy crew, and a real promise that the job gets done right. That’s what we do. Call (747) 966-3037 for a free estimate from Luis and the Meadowsweet team. A live person answers, any hour, any day. Shoe covers on, drop cloths down, and a photo of the clean-up before we leave. Always.
Written by Luis Serrano, Owner at Meadowsweet Heating & Air, serving Fresno and the surrounding Central Valley.